Programmable Lighting Controllers configured as
Traffic Controllers / Sequencers
(not to be confused with illegal pre-emption light-changing units)
SYNC-3 (3-output) Traffic Signal Controller Controls one 3-light Signal
$59.00 (CURRENTLY OUT OF STOCK)
SYNC-5 (5-Output) Expandable / Linkable Traffic Signal Controller
Detailed Specifications
$69.00
SYNC-DC 12 VDC Relay Based Controller
Power input : 12VDC Output: Isolated relay dry-contacts rated 10A
(instructions (PDF))
$57.00
INQUIRE
New Item!
Booster!
Relay Board to be used in conjunction with a SYNC controller
Purpose: To "BOOST" the output capacity of lower wattage controllers to achieve higher switching capacities/amperages. The controller only needs to provide the low current to power the relays, and the high capacity relays provide the 'brute force' switching capacity to drive the heavy loads. Also works with other triac based controllers on the market.
Has five 16-Amp relays with 120 VAC coils compatible with the outputs of the SYNC controllers. 5-input screw terminal to match the C R Y G W DW terminals of the SYNC-5 board. 5-screw isolated output terminal for the relay output contacts. Outputs screw terminals are rated 10 Amps at 120 VAC. Because the outputs are isolated from the power source (input terminals), outputs can be wired to switch low-voltage lighting (12-24 vdc)
Booster Wiring Diagram (.pdf 22k)
$42.00
IR Relay Board
<--- Click on picture for larger image
3-Output Controller with IR remote control programming and Relay outputs. Input voltage is 120 VAC. Outputs are rated 7 Amps @ 120VAC. (700 watts)
Standard Green - Yellow - Red sequence. Timing for each output can be set independantly from 1 second to 20 minutes. Includes Pre-Programmed Universal remote .
Dimensions: 3.5" wide X 3.1" tall X 1.2" high (does not include stand-off height)
Install Instructions (.pdf)
Universal Remote button functions:
CHANNEL UP = AUTO-SEQUENCE MODE / auto advance through the G-Y-R cycles.
1 = TURN ON GREEN LIGHT (manual mode)
2 = TURN ON YELLOW LIGHT (manual mode)
3 = TURN ON RED LIGHT (manual mode)
4 = CAUTION MODE flashing RED
5 = CAUTION MODE flashing YELLOW
6 = CAUTION MODE alternating RED/YELLOW
0+0+0 = start "time-set" auto sequence / time setting routine
POWER BUTTON = turns signal ON/OFF
$89.88 + S/H
INQUIRE
Detailed Specifications
$69.00
SYNC-DC 12 VDC Relay Based Controller
Power input : 12VDC Output: Isolated relay dry-contacts rated 10A
(instructions (PDF))
$57.00
INQUIRE
New Item!
Booster!
Relay Board to be used in conjunction with a SYNC controller
Purpose: To "BOOST" the output capacity of lower wattage controllers to achieve higher switching capacities/amperages. The controller only needs to provide the low current to power the relays, and the high capacity relays provide the 'brute force' switching capacity to drive the heavy loads. Also works with other triac based controllers on the market.
Has five 16-Amp relays with 120 VAC coils compatible with the outputs of the SYNC controllers. 5-input screw terminal to match the C R Y G W DW terminals of the SYNC-5 board. 5-screw isolated output terminal for the relay output contacts. Outputs screw terminals are rated 10 Amps at 120 VAC. Because the outputs are isolated from the power source (input terminals), outputs can be wired to switch low-voltage lighting (12-24 vdc)
Booster Wiring Diagram (.pdf 22k)
$42.00
IR Relay Board
<--- Click on picture for larger image 3-Output Controller with IR remote control programming and Relay outputs. Input voltage is 120 VAC. Outputs are rated 7 Amps @ 120VAC. (700 watts)
Standard Green - Yellow - Red sequence. Timing for each output can be set independantly from 1 second to 20 minutes. Includes Pre-Programmed Universal remote .
Dimensions: 3.5" wide X 3.1" tall X 1.2" high (does not include stand-off height)
Install Instructions (.pdf)
Universal Remote button functions:
CHANNEL UP = AUTO-SEQUENCE MODE / auto advance through the G-Y-R cycles.
1 = TURN ON GREEN LIGHT (manual mode)
2 = TURN ON YELLOW LIGHT (manual mode)
3 = TURN ON RED LIGHT (manual mode)
4 = CAUTION MODE flashing RED
5 = CAUTION MODE flashing YELLOW
6 = CAUTION MODE alternating RED/YELLOW
0+0+0 = start "time-set" auto sequence / time setting routine
POWER BUTTON = turns signal ON/OFF
$89.88 + S/H
INQUIRE
CLICK HERE TO BUY
| Contact
F.A.Q.
Support
HOME |
These controllers can also be used for other lighting applications as well.
Controllers can be custom-programmed for alternate lighting sequences.